Multiyear Performance of a Pervious Concrete Infiltration Basin BMP

The use of infiltration storm-water best management practices (BMPs) has become a more commonly used approach as a means of reducing postdevelopment runoff volumes in many areas throughout the United States. Although studies regarding the performance of infiltration BMPs are emerging, much remains to be learned about their design, construction, and operation. The increase in knowledge will improve the performance and longevity of these BMPs. The performance of one such infiltration basin over a 2-year cycle is presented in this paper. The study site is a pervious concrete infiltration basin BMP built in 2002 in a courtyard common area at Villanova University. The system consists of three linked infiltration beds lined with geotextile filter fabric, filled with coarse aggregate, and overlaid with pervious concrete. The natural soil beneath the infiltration BMP is a silty sand. The BMP is extensively instrumented to facilitate water quantity and quality research. Both water-quantity and -quality results are presented. The water-quantity analysis showed that the performance of the basin was directly related to its infiltration characteristics. The infiltration rate of the silty sand is cyclic, with higher rates during warmer periods and lower rates during colder periods. The water quality analysis investigated the pollutant reduction for chloride, copper, nitrogen, and phosphorus from the inlet to the surface-water outlet of the structure, as well as differences in pollutant concentration levels between the basin, surrounding ground, and varying soil layer elevations beneath the basin. In general, the pollutant reduction to the surface waters was greater than 90% from inlet to outlet, primarily influenced by the infiltration of the storm water into the natural soils below the BMP. The pollutant concentration of the infiltrating runoff was found to be higher than expected in the area adjacent to the bed when compared to concentration levels found at a similar depth beneath the infiltration bed. Comparison of pollutant concentration levels, as the water moved from within the storage bed to the soil beneath the bed, were shown to vary, with statistical differences found for mean concentration levels of both pH and copper levels; and no statistical differences were found for conductivity, total phosphorous, and chloride at each elevation.     

Impact of selective oxidation during inline annealing prior to hot-dip galvanizing on Zn wetting and hydrogen-induced delayed cracking of austenitic FeMnC steel

The present study discusses the impact of selective oxidation during in-line annealing of Fe–23%Mn–0.6%C–0.3%Si steel on surface and sub-surface properties and is focused on hot-dip galvanizability and susceptibility to hydrogen-induced delayed cracking. Annealing temperature (700–1100 °C) and dewpoint DP (? 15/?30/?50 °C) of the 5%H₂–N₂ annealing atmosphere were varied in order to investigate Zn wetting in dependence on selective oxidation of Mn and Si. Sub-surface microplasticity (hardness, pop-in frequency, pop-in activation load) was examined by electrochemical nanoindentation in-situ to hydrogen charging (ECNI) to assess hydrogen/material interactions. Zn wetting fails if external Mn and Si oxidation is not avoided by performing high reductive bright annealing (1100 °C/DP ? 50 °C). Zn wetting will however turn to increase if a roughly globular MnO layer appears and Si is internally oxidized (700–900 °C/DP ? 15 °C). Selective oxidation further affects hydrogen/material interactions by influencing the local distribution of solid-soluted Mn: ECNI results indicate hydrogen-induced dislocation demobilization (HEDE mechanism) or dislocation mobilization (HELP mechanism) in dependence on the local amount of solid-soluted Mn within the sub-surface. Macroscopic delayed cracking seems to occur earlier if HELP is predominating. The gained results benefit understanding the impact of selective oxidation on galvanizability and susceptibility to hydrogen-induced failure of austenitic FeMnC steel and advance further developments in processing high Mn alloyed steels.     

Production of microparticles from milk fat products using the Supercritical Melt Micronization (ScMM) process

The ScMM (Supercritical Melt Micronization) process was applied for the production of microparticles from anhydrous milk fat (AMF) and a diacylglycerol-based modified milk fat (D-AMF). Both fats were able to dissolve ca. 30 wt% CO₂ in the studied pressure and temperature ranges, being the CO₂ amount slightly higher for AMF. A melting point depression was observed in both systems in the presence of CO₂. Two powder morphologies were obtained (spherical hollow particles and a mass sponge-like broken particles) depending on the ScMM process conditions. The concentration of CO₂ in the fat melt was the main process variable affecting the particle morphology, followed by the temperature of the melt. The small broken particles originated from the breakage of spherical fat particles that solidified before all CO₂ could escape from the atomized droplets. While the hollow spheres had a tendency to agglomerate, the broken microparticles constituted a free-flowing powder as long as they were stored at low temperatures (up to −18 °C). Both types of particles have a potential for being incorporated in refrigerated or frozen food products as a structuring agent.     

Maximizing efficiency in the transition to a coal-based economy

Energy is the lynchpin of modern society. Since the early 1970s, growing dependence on foreign energy sources, oil in particular, has constrained US independence in foreign policy, and at times, inhibited economic stability and growth. Addressing oil dependence is politically and economically complex. Proposed solutions are multifaceted with various objectives such as energy efficiency and resource substitution. One solution is the partial transition from an oil- to coal-based economy. A number of facts support this solution including vast coal reserves in the US and the relative price stability of coal. However, several roadblocks exist. These include uncertain recoverable reserves and the immaturity of “clean” coal technologies. This paper provides a first order analysis of the most efficient use of coal assuming the transition from oil to coal is desirable. Scenario analysis indicates two possible transition pathways: (1) bring the transportation sector onto the electric grid and (2) use coal-to-liquid fuels to directly power vehicles. The feasibility of each pathway is examined based on economic and environmental factors, among which are energy availability, affordability and efficiency, and environmental sustainability. Results indicate that partial transition of the transportation sector onto the electric grid offers the more viable solution for coal-based reduction of the US oil dependence.     

3D printing of bone substitute implants using calcium phosphate and bioactive glasses

Customized implants for bone replacement are a great help for a surgeon to remodel maxillofacial or craniofacial defects in an esthetical way, and to significantly reduce operation times. The hypothesis of this study was that a composite of β-tricalcium phosphate (β-TCP) and a bioactive glass similar to the 45S5 Henchglass^® is suitable to manufacture customized implants via 3D-printing process. The composite was chosen because of the bioresorption properties of the β-TCP, its capability to react as bone cement, and because of the adjustability of the bioactive glass from inert to bioresorbable. Customized implants were manufactured using the 3D-printing technique. The four point bending strength of the printed specimens was 14.9 MPa after sintering. XRD analysis revealed the occurrence of two other phases, CaNaPO₄ and CaSiO₃, both biocompatible and with the potential of biodegradation. We conclude that it is possible to print tailored bone substitute implants using a bioactive TCP/glass composite. The glass is not involved as reactive substance in the printing process. This offers the opportunity to alter the glass composition and therefore to vary the composition of the implant.     

Five decades of Computer-Aided Ship Design

This article will present a synoptical review of key developments in Computer-Aided Ship Design since its inception about five decades ago. Milestone events and major innovations will be identified in several categories of ship design application with the principal emphasis on the methodologies, the modeling and the integration of the ship design process. The discussion will address many specific subtasks of ship design on the common platform of a human-guided, computer-based decision process.